Original Factory Illustrated Operating Manual (User Manual) for Linde Forklift Truck 316-03 Series With Diese Lengine

Covered models:
S30
S40
S50
S60

Format: PDF, 84 pages
Language: English

Table of contents

DESCRIPTION
Your Linde Fork Lift Truck
Technical Note
Taking over Inspection
Type Plates
Technical data
Technical description
General view of truck
Controls and Indicators
Gauges and warning lights
BEGINNING OPERATION
Safety rules
Opening the side panels
Opening the bonnet
Opening the door (front opening)
Retaining the door (front opening)
Closing the door from inside (front door)
Closing the door from outside (front door)
Opening the door (side opening)
Retaining the door (side opening)
Closing the door from inside (side door)
Closing the door from outside (side door)
Applying the seat belt (front opening)
Opening the seat belt (front opening)
Applying the seat belt (side opening)
Opening the seat belt (side opening)
Daily checks and servicing before operation
Check engine oil level
Check fuel level
Check engine coolant level
Check brake fluid level
Working, travel and steering hydraulic systems
Check oil level
Top up oil
Check tyre condition and pressure
Drive and steer axle tyre specification
Adjusting the drivers seat
Starting the engine
Normal start
Cold start
Emergency startup
Stopping the engine
Engine malfunctions
OPERATION
Travel
Controlled low speed travel
Forward travel
Reverse travel
Changing direction of travel
Stopping the truck
Steering and braking
Steering
Service brake
Parking brake
Cab interior light, fuses, lighting
Operating the cab interior light
Fuses
Turning on the lights
Horn, indicators, hazard warning, working lights
Turning on the indicator lights
Operating the horn
Turning on the hazard warning lights
Turning on working lights
Windscreen wipers, washer, ventilation
Turning on the windscreen wipers
Turning on the rear windscreen wipers
Turning on the top windscreen wipers
Turning on the windscreen washer
Turning on the ventilation
Heater control
Operating the lifting device and attachments
Control levers
Lifting the lifting device
Lowering the lifting device
Tilting the deck up
Tilting the deck down
Traverse the lifting device - inwards
Traverse the lifting device - outwards
Operating optional attachments
Operating the sideshift
Before lifting a load
Load capacity plate
Lifting a load
Adjusting the fork spread
Lifting a load
Travelling with loads
Depositing the load
Before leaving the truck
Trailer coupling, wheel change
Trailer coupling
Locations for jacks when changing wheels
Hoisting the truck
Hoisting the truck
Towing instructions
Towing away
Towing procedure
After towing
General information
Before attempting any service work ensure:
MAINTENANCE
Work on the lifting device
Securing the lifting device
Securing the raised lifting device
Securing the lifting device against retracting
Securing the deck against tilting
Standard lifting device operation
Checks and maintenance work after the first 50 hours
Inspection and maintenance chart
Inspection and maintenance as required
Cleaning the truck
Cleaning and spraying the lift chains
Cleaning the air filter
Check the dust valve
Tightening wheel nuts
Check and clean the radiator and hydraulic oil cooler
Bleeding the fuel system
Bleeding the fuel lines
Check brake fluid level
Check windscreen washer bottle level
Battery condition check
Check hydraulic and electrical systems
Lubrication points
Lubricate the steer axle
Lubricate the drive axle central pivots
Lubricate cab door hinges
Traverse cylinder rod end lubrication
Mast lubrication points
Check V-belt tension and condition
500-hour Inspection and maintenance
Change engine oil
Renew engine oil filter
Top up engine oil
Cleaning the fuel sediment bowl
Lubricate the parking brake
Check condition and mounting of lifting device
and lift chain
Adjusting traverse cylinder setting
Check forks and fork locking device
Check and clean the brake system
Check brake linings
Steer axle bearing check
Fuel filter change
Fuel pump check
Check hydraulic and electrical systems
Drive axle differential oil level
Check engine coolant strength
Working hydraulic suction filter change
Travel hydraulic filter change
Drive axle hub oil level check
1000-hour Inspection and maintenance
Check cooling system for leaks and tightness
Check air intake system for leaks and tightness
Check exhaust system for leaks and tightness
Air filter element change
Check traverse and lifting device roller bearings
Check drive and steer axle mountings
Check engine mountings
Valve tip clearance check
Check injection nozzle
2000-hour Inspection and maintenance
Check travel hydraulic pump mountings
Check travel hydraulic motor mountings
Drive axle oil change
Working hydraulic oil change
2500-hour Inspection and maintenance
Check engine accesories equipment
Inspection and maintenance data
Fuel and oil recommendations
Electric circuit diagram
Hydraulic circuit diagram
Alphabetical index